surface mount ceramic chip capacitors extended values 0805, x7r dielectric, 25, 50, 100, 200 volts 25 volts ? 0.56f 50 volts ? 0.12 - 0.22f 100 volts ? 56,000 - 120,000pf 200 volts ? 8,200 - 56,000pf table 1 dimensions - millimeters new product release outline drawings f3273a 04/05 eia size code metric size code (ref) l# length w# width thickness b bandwidth s min. separation mounting technique 0805* 2012 2.0 (.079) 0.2 (.008) 1.25 (.049) 0.2 (.008) see table 2 0.5 (.02) .25 (.010) 0.75 (.030) solder wave or solder reflow cap values kemet part number capacitance tolerance thickness - mm qty 7? reel qty 13? reel 0.56f c0805c564(1)3rac j,k,m 1.25 0.15 2,500 10,000 0.12f c0805c124(1)5rac* j,k,m .90 .10 4,000 10,000 0.15f c0805c154(1)5rac* j,k,m .90 .10 4,000 10,000 0.18f c0805c184(1)5rac* j,k,m .90 .10 4,000 10,000 0.22f c0805c224(1)5rac* j,k,m .90 .10 4,000 10,000 56,000pf c0805c563(1)1rac j,k,m 1.00 0.10 2,500 10,000 68,000pf c0805c683(1)1rac j,k,m 1.00 0.10 2,500 10,000 82,000pf c0805c823(1)1rac j,k,m 1.00 0.10 2,500 10,000 100,000pf c0805c104(1)1rac j,k,m 1.00 0.10 2,500 10,000 120,000pf c0805c124(1)1rac j,k,m 1.25 0.15 2,500 10,000 8,200pf c0805c822(1)2rac j,k,m .78 0.10 2,500 10,000 10,000pf c0805c103(1)2rac j,k,m .78 0.10 2,500 10,000 12,000pf c0805c123(1)2rac j,k,m .78 0.10 2,500 10,000 15,000pf c0805c153(1)2rac j,k,m .78 0.10 2,500 10,000 18,000pf c0805c183(1)2rac j,k,m .78 0.10 2,500 10,000 22,000pf c0805c223(1)2rac j,k,m .78 0.10 2,500 10,000 27,000pf c0805c273(1)2rac j,k,m 1.00 0.10 2,500 10,000 33,000pf c0805c333(1)2rac j,k,m 1.00 0.10 2,500 10,000 39,000pf c0805c393(1)2rac j,k,m 1.00 0.10 2,500 10,000 47,000pf c0805c473(1)2rac j,k,m 1.25 0.15 2,500 10,000 56,000pf c0805c563(1)2rac j,k,m 1.25 0.15 2,500 10,000 table 2 - ratings & part number listing to complete the kemet part number, insert capacitance tolerance: j - 5%, k - 10% or m 20%. * x7r dielectric - extended range values - cap and df measured at 0.5 vrms.
in general, the information in the kemet surface mount catalog f3102 applies to these capacitors. the information in this bulletin supplements that in the catalog. electrical parameters as detailed in the kemet surface mount catalog f3102 for x7r, with following specific requirements based on room temperature (25c) parameters: ? operating range: -55c to +125c, with no-bias capacitance shift limited to 15% over that range ? insulation resistance (ir) measured after 2 minutes at rated voltage @ 25c: limit is 1000 megohm microfarads or 100 gigohms, whichever is less. ? capacitance and dissipation factor (df) measured at 1khz at 1.0vrms. 25 volts - df limit is 3.5% > 25 volts - df limit is 2.5% soldering process wave soldering or reflow soldering is acceptable for these chips. marking these chips are normally supplied unmarked. if required, they can be laser marked as an extra cost option. more detail on the marking format is included in our surface mount catalog f3102. ? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 ? (864) 963-6300 ? www.kemet.com
|
